亲爱的研友该休息了!由于当前在线用户较少,发布求助请尽量完整地填写文献信息,科研通机器人24小时在线,伴您度过漫漫科研夜!身体可是革命的本钱,早点休息,好梦!

Field joint coating of pipelines – effect of soluble salt contamination on 2-layer heat shrink sleeve performance

涂层 环氧树脂 阴极保护 管道运输 图层(电子) 材料科学 腐蚀 复合材料 接头(建筑物) 焊接 海底管道 污染 冶金 结构工程 环境科学 地质学 岩土工程 工程类 电化学 化学 环境工程 电极 物理化学 生态学 生物
作者
Frazer Howard Smith
出处
期刊:Anti-corrosion Methods and Materials [Emerald Publishing Limited]
卷期号:63 (2): 105-115 被引量:8
标识
DOI:10.1108/acmm-09-2015-1573
摘要

Purpose – During offshore pipe-lay, pipe lengths with anticorrosion coating are welded together, and, to facilitate the welding process, the ends of the pipe remain uncoated. A wide range of field joint coating (FJC) types is available for coating this bare section, functioning in conjunction with the pipeline cathodic protection system to provide an anti-corrosion system or package. This paper aims to relate to two-layer type heat shrink sleeves (2LHSS), which commonly are used for FJC of concrete-weighted offshore pipelines where the sleeve typically is over-coated with a solid or foam type polyurethane “infill”. Similar sleeves also are used sometimes in exposed conditions on lines without concrete over-coating. The maximum allowable soluble salt contamination prior to application of high-performance coating systems can vary, depending upon the coating type, but typically has been set at 20 mg/m2 (de la Fuente et al. , 2006). The first layer of three-layer heat shrink sleeve (3LHSS) systems for pipeline FJC, liquid epoxy, falls into this category (ISO_21809-3:2008, 2008). In contrast, the 2LHSS system does not use a liquid epoxy first layer but relies instead on the bonding of a “mastic” layer directly to the pipe metal surface. The maximum acceptable concentration of salt contamination on prepared metal surfaces prior to the application of 2LHSS has been a subject of debate and was the focus of this study. International standards for FJC do not provide a maximum salt level. However, some companies have continued to specify low thresholds for the maximum allowable salt level for 2LHSS, which can result in expensive delays in production during offshore pipe-lay. In this study, salt contamination levels of up to 120 mg/m2 were found to have no effect on peeling performance after accelerated aging by hot water immersion. Furthermore, preparation for welding and the use of potable water during ultrasonic testing procedures prior to FJC, typically reduces the salt contamination level to below 50 mg/m2 providing a strong case for the deletion of salt contamination testing for 2LHSS. Design/methodology/approach – The potential risk of failure of the coating due to poor surface cleanliness/contamination was assessed by testing the adhesion between the coating and the steel substrate to which the coating is adhering, following a period of hot water immersion. Compliance with ISO 21809-3 “Annex I” requires 28 days’ immersion at maximum operating temperature. For this study, to create a severe situation, the test rings were subjected to accelerated aging by water immersion at the HSS upper specified temperature of 65°C for more than twice the specified period (ISO_21809-3:2008, 2008). Two HSS were tested; one was widely used in applications where exposure to moderate mechanical stress is required, having a high shear strength type mastic “hybrid” adhesive containing a significant proportion of amorphous polypropylene blended with tackifiers and ethylene vinyl acetate (EVA), Andrenacci et al. (2009) referred to as “Type A”. The second, referred to as “Type B”, is widely used in applications where it is covered by a layer of “infill”, typically consisting of polyurethane foam or solid polyurethane elastomer, i.e. typical design methodology for concrete coated pipelines. “Type B” HSS had a more moderate strength traditional type mastic than “Type A” containing a significant percentage of butyl rubber with asphalt, activation agents and tackifying resins. To determine how to apply the salt contamination without causing flash rust, a mini-study was completed on the steel substrate. After numerous trials, it was found impossible to not to form visible rust on the pipe surface. The extent of rusting was minimised by heating the pipe immediately after the application of the salt solution. Findings – High levels of sea salt on power tool prepared pipe surfaces were investigated by peel testing of 2LHSS after hot water immersion and compared against peel tests undertaken prior to hot water immersion. The test conditions were considered severe: salt contamination levels of up to 120 mg/m2 applied on power tool cleaned pipe surfaces that had been aged for one year without prior grit blasting. The accelerated ageing procedure had twice the specified (ISO_21809-3:2008, 2008) water immersion duration, and the test samples had exposed edges providing the possibility for moisture to creep under the coating. The test results showed that there were no noticeable deleterious effects on the performance of the two most commonly used FJCs, 2LHSS. Therefore, it was concluded that, as the level of salt contamination on prepared pipe surfaces after wet non-destructive testing typically is much lower than the levels tested in this study, pipe surfaces prepared for the application of 2LHSS type do not require specific additional measures to further reduce salt contamination, provided that care is taken to ensure that these conditions are maintained consistently during pipe laying operations. Practical implications – The frequency of salt contamination testing of power tool cleaned surfaces prior to mastic type heat shrink sleeves can be minimised, and perhaps omitted entirely, provided the above criteria are satisfied. Originality/value – A literature review revealed there was little published information on the testing of 2LHSS and nothing related to hot water immersion testing. Hence, the results of this investigation have provided useful industrial data regarding the effect of hot water ageing and the influence of surface salt contamination on field joint corrosion prevention capabilities.

科研通智能强力驱动
Strongly Powered by AbleSci AI
科研通是完全免费的文献互助平台,具备全网最快的应助速度,最高的求助完成率。 对每一个文献求助,科研通都将尽心尽力,给求助人一个满意的交代。
实时播报
21秒前
爱听歌的香萱完成签到,获得积分10
29秒前
务实的绮琴完成签到,获得积分10
35秒前
54秒前
精明夜安完成签到,获得积分10
1分钟前
1分钟前
忧心的曼凝的应助被liuqiwei采纳,获得10
1分钟前
43tg完成签到,获得积分10
1分钟前
卫半山完成签到 ,获得积分10
1分钟前
落后的雨筠完成签到,获得积分10
1分钟前
qfhbg完成签到,获得积分10
1分钟前
wetg完成签到,获得积分10
1分钟前
portik完成签到,获得积分10
1分钟前
1分钟前
东方完成签到,获得积分10
1分钟前
仁爱的鲂完成签到,获得积分10
1分钟前
hgjk完成签到,获得积分10
1分钟前
sdf完成签到,获得积分10
1分钟前
amz完成签到,获得积分10
1分钟前
称心的以蕊完成签到,获得积分10
1分钟前
adefgv完成签到,获得积分10
1分钟前
fhjg完成签到,获得积分10
1分钟前
jtk完成签到,获得积分10
1分钟前
pwn完成签到,获得积分10
1分钟前
wh完成签到,获得积分10
2分钟前
fsw完成签到,获得积分10
2分钟前
sd完成签到,获得积分10
2分钟前
li1完成签到,获得积分10
2分钟前
EK1完成签到,获得积分10
2分钟前
孤独的富完成签到,获得积分10
2分钟前
fr1完成签到,获得积分10
2分钟前
xi完成签到 ,获得积分10
2分钟前
爆米花的应助被b1gcat采纳,获得10
2分钟前
XE1完成签到,获得积分10
2分钟前
贪玩书翠完成签到,获得积分10
2分钟前
FR完成签到,获得积分10
2分钟前
ly完成签到,获得积分10
2分钟前
XE完成签到,获得积分10
2分钟前
EC完成签到,获得积分10
2分钟前
LY完成签到,获得积分10
2分钟前
高分求助中
(应助此贴封号)【重要!!请各用户(尤其是新用户)详细阅读】【科研通的精品贴汇总】 10000
拉伸高分子熔体中缠结行为的模拟和小角中子散射研究 1700
The World Atlas of Wine 9th edition 1000
奈特基础组织学:配套组织病理学(第4版)(Netter's Essential Histology With Correlated Histopathology) 800
八旗制度の研究 600
高分子基功能界面水蒸发材料与应用研究 500
外场增强的水汽发电研究 500
热门求助领域 (近24小时)
化学 材料科学 医学 生物 纳米技术 计算机科学 工程类 有机化学 化学工程 生物化学 物理 复合材料 内科学 催化作用 光电子学 人工智能 细胞生物学 无机化学 物理化学 数学
热门帖子
关注 科研通微信公众号,转发送积分 8185298
求助须知:如何正确求助?哪些是违规求助? 9574106
关于积分的说明 21834276
捐赠科研通 7782800
什么是DOI,文献DOI怎么找? 3434540
关于科研通互助平台的介绍 2558812
邀请新用户注册赠送积分活动 2481237