作者
ZHAO Rongman,Jinlun Zhou,LIU Sen,PENG Haiyan,ZHANG Yun,Huamin Zhou,Xiaolin Xie
摘要
Objective Most domestic holographic plastic processing equipment still relies on embossed holography technology. This traditional technology cannot fabricate reflection volume holograms that possess three-dimensional (3D) effects visible to the naked eye, nor can it meet the high quality printing requirements for holographic optical elements (HOE). To satisfy the urgent demand for advanced processing equipment within the field of holographic plastics manufacturing, a holographic wavefront printing equipment termed HG-I was designed and manufactured. This system demodulated and projected a computer-generated hologram (CGH) through a phase-only spatial light modulator (SLM) onto a photosensitive polymer material, causing the object light carrying information to interfere with a reference beam. The final goal of this research was to print holographic plastics successfully and fabricate reflection volume holograms with naked-eye visible three-dimensional effects.Methods The investigation began with an analysis of the diffracted light field of the object beam from both theoretical and experimental levels. The unfavorable effects and structural characteristics introduced by the discrete pixel structure of the SLM within the object diffraction field were systematically evaluated. To suppress these discrete artifacts, two improvement methods were proposed, utilizing a spatial band-pass filter and a digital blazed grating, respectively. Subsequently, corresponding 4f optical filtering systems were constructed within the optical path. These experimental setups were utilized for quantitative testing and comprehensive comparative analysis, focusing primarily on two core indicators: the spatial spectral distribution and the object light energy utilization. Second, the system was optimized at the optical design level to balance the inherent trade-off between the size of the individual holographic element and the overall viewing angle. A set of exchangeable telecentric lens groups with magnification ratios of 1 and 1/7.5 was designed and manufactured, respectively. This hardware adaptation satisfied the printing requirements across different scenarios. Furthermore, motion planning strategies were optimized and studied. Theoretical analysis was combined with experimental validation to investigate how different scanning paths affected stitching gaps, specifically comparing the differences between the S-shaped path and the unidirectional path. Finally, the overall printing quality of large-scale volume holograms was optimized by introducing an overlap splicing strategy for adjacent holographic elements alongside a cyclic exposure process.Results and Discussions Experimental results indicated that both filtering schemes worked effectively when critical conditions were met. High-order repeated ghost images were effectively eliminated when the filter aperture reached the critical threshold conditions. Quantitative measurements revealed that the aperture size influenced the energy utilization of object light. Under identical aperture conditions, the band-pass filtering method increased the energy utilization of object light by up to 199.4% compared with the digital blazed grating method. Additionally, the band-pass filtering method offered the advantage of a simpler optical path alignment in practical applications, though it simultaneously introduced a loss of low-frequency spectral information. Furthermore, the introduction of the exchangeable telecentric lens groups allowed the equipment to adapt to different application scenarios. This lens system successfully achieved a balance between two modes: the first was the high-efficiency printing of large-scale two-dimensional (2D) holograms corresponding to a small viewing angle (8.15°), and the second was 3D displays requiring a wide viewing angle (64.47°). Regarding mechanical motion planning, the translation stage trajectories were evaluated and analyzed. The results demonstrated that a unidirectional printing path effectively avoided the gap misalignment problem between odd rows and even rows. Finally, implementing a 50% overlap splicing strategy combined with a multi-cycle low-dose exposure process effectively improved the quality of the boundary regions. The row gap width decreased from an initial 355 μm to 231 μm, and the column gap width dropped from 420 μm to 300 μm. Moreover, data analysis confirmed that the average grayscale deviation decreased from 0.413 to 0.030 for row gaps, and from 0.380 to 0.090 for column gaps. These quantitative results indicated that the microscopic stitching seams were significantly weakened, and the overall visual fragmentation degree of the large-scale holograms was markedly reduced.Conclusions The developed reflection volume holographic wavefront printing equipment (HG-I) realized the independent development of the optical system design and the control software system, which together constituted a relatively complete hardware-software integrated equipment system. The equipment possessed the capability for stable, continuous operation over long periods, and it can successfully fabricate reflection volume holograms that reconstruct under white light conditions while preserving complete three-dimensional depth and parallax information. Implementing the overlap splicing and cyclic printing process can effectively optimize the printing quality of large-scale holograms. This research provided a verified hardware and software configuration along with a processing method, establishing a foundation for the development of advanced domestic processing equipment in holographic plastics manufacturing.