Influence of Overlaps on Towpreg Bonding in Automated Fiber Placement: Experiment, Simulations and Compaction Roller Design

作者
Amir Hafez Yas
出处
期刊:Concordia University - Spectrum Research Repository
摘要

Automated Fiber Placement (AFP) enables precise and flexible composite manufacturing but remains sensitive to surface irregularities and disturbances in process parameters. Among common defects, tape overlaps can introduce surface irregularities that create regions of insufficient inter-laminar bonding in the uncured state and promote secondary defects such as wrinkling or bridging during subsequent layup passes. Understanding how overlaps interact with roller behavior and process conditions is therefore essential. The influence of roller stiffness and geometry on pressure distribution was studied with and without an overlap. Experiments and finite element analyses showed that softer rollers conform more effectively to overlap-induced height variations but deliver reduced pressure, while stiffer rollers maintain higher pressure but leave larger uncovered regions. To capture the effects of process parameters on bonding, an in-house AFP simulation setup was used to fabricate single-lap joint (SLJ) specimens under controlled compaction force, temperature, and feed rate. The resulting shear strength measurements demonstrated that bonding performance arises from the interaction among these variables rather than from any single parameter. A complementary finite element model accurately predicted the shear response of the uncured interfaces, confirming its suitability for representing interlayer bonding. Motivated by the role of roller behavior near overlaps, new polyurethane compaction rollers with increased shaft diameters (increased from 25 mm to 28, 32, and 35 mm) and softer outer layers were designed to reduce pressure discontinuities while preserving adequate overall compaction force. Captured compaction pressures, microscopic images, SLJ tests, and FEM simulations confirmed that these rollers reduce the width of the affected zone and produce more uniform bonding thickness compared with conventional designs once an overlap is present. To mitigate overlap-induced disruptions in compaction pressure, further investigations were conducted to examine compaction-roller behavior on complex mold geometries where curvature itself can amplify pressure non-uniformity. Accordingly, concave and convex molds with radii of 100 mm were selected as representative non-flat surfaces. An alternative compaction roller design approach was then introduced to improve conformity while maintaining adequate compaction pressure, with key design parameters (e.g., shaft concave depth and convex height) selected based on FEM results to promote more uniform pressure distribution on both concave and convex geometries. Overall, the results provide a comprehensive understanding of how overlaps, roller characteristics, and process parameters collectively influence bonding quality in AFP, offering a method to improve pressure distribution and inter-laminar bonding.

科研通智能强力驱动
Strongly Powered by AbleSci AI
科研通是完全免费的文献互助平台,具备全网最快的应助速度,最高的求助完成率。 对每一个文献求助,科研通都将尽心尽力,给求助人一个满意的交代。
实时播报
禹hs发布了新的文献求助10
刚刚
DW的应助被陈婕采纳,获得10
刚刚
1秒前
辛勤的绮兰完成签到,获得积分10
2秒前
2秒前
鱼鱼完成签到,获得积分10
3秒前
3秒前
在水一方的应助被675675采纳,获得10
5秒前
幸福台灯完成签到,获得积分10
5秒前
Captainhana完成签到,获得积分10
7秒前
8秒前
嘤嘤嘤发布了新的文献求助10
9秒前
三千白发生完成签到,获得积分10
9秒前
纳古菌完成签到,获得积分10
10秒前
SG完成签到,获得积分10
10秒前
听话的无极完成签到,获得积分10
10秒前
10秒前
123456完成签到,获得积分10
11秒前
努力小人完成签到,获得积分10
11秒前
12秒前
liang完成签到,获得积分10
12秒前
12秒前
青葙完成签到,获得积分10
13秒前
123456发布了新的文献求助10
14秒前
11NING发布了新的文献求助10
15秒前
Ysk完成签到,获得积分10
15秒前
17秒前
675675发布了新的文献求助10
19秒前
汉堡包的应助被小艾同学采纳,获得10
19秒前
20秒前
23秒前
11NING完成签到,获得积分10
23秒前
23秒前
SCI完成签到,获得积分10
24秒前
Koi发布了新的文献求助10
24秒前
禹hs完成签到,获得积分10
27秒前
吱ing完成签到 ,获得积分10
28秒前
ding的应助被bbb采纳,获得10
28秒前
SCI发布了新的文献求助10
28秒前
ZeSheng完成签到,获得积分10
29秒前
高分求助中
(应助此贴封号)【重要!!请各用户(尤其是新用户)详细阅读】【科研通的精品贴汇总】 10000
拉伸高分子熔体中缠结行为的模拟和小角中子散射研究 1700
The World Atlas of Wine 9th edition 1000
奈特基础组织学:配套组织病理学(第4版)(Netter's Essential Histology With Correlated Histopathology) 800
八旗制度の研究 600
Boundaries and Bodhisattvas 500
高分子基功能界面水蒸发材料与应用研究 500
热门求助领域 (近24小时)
化学 材料科学 医学 生物 纳米技术 计算机科学 工程类 有机化学 化学工程 生物化学 物理 复合材料 内科学 催化作用 光电子学 人工智能 细胞生物学 无机化学 物理化学 数学
热门帖子
关注 科研通微信公众号,转发送积分 8181658
求助须知:如何正确求助?哪些是违规求助? 9571454
关于积分的说明 21818081
捐赠科研通 7777987
什么是DOI,文献DOI怎么找? 3433508
关于科研通互助平台的介绍 2557696
邀请新用户注册赠送积分活动 2479568