摘要
Nowadays, the lithium-rich layered 3d-transition-metal (TM) oxides (LLOs) are regarded as one of the most attractive cathode materials for next-generation lithium-ion batteries (LIBs), because they can exhibit a discharge capacity (approaching 300 mAh g$^{-1}$ at 0.1 C) much higher than that of the currently used materials(~ 180 mAh g$^{-1}$at 0.1 C). However, the formation mechanism of LLOs has not been fully understood on a fundamental level yet.One of the most interesting and still open questionsis aboutlithium and oxygen atoms are incorporatedinto the precursor’s crystal structure during the synthesisoffinal LLO products.Asystematic exploration of this subject was conducted in this PhD work. In order to obtain the desired LLOs with high performance, it is necessaryto design apropermorphology for the precursor which acts as an important source for the high-temperature lithiation reaction. A powerful hydroxide coprecipitation processwas employedto synthesizethe three dimensional (3D) nanoflower-structured precursor for LLOs. A combination of thermogravimetric (TG), differential scanning calorimetric (DSC) and in situhigh-temperature synchrotron radiation diffraction (SRD) experiments was utilized to investigate the thermally induced structural evolution. The results showthat the precursor composedof layered TMOOH (C2/m) and tetragonal TM$_3$O$_4$(I41/amd) transformsinto a single cubic spinel TM$_3$O$_4$phase (Fd$\bar{3}$m) withsuccessive oxygen lossduring thermal treatment. On the contrary, oxygen would beinsertedinto the host structure during synthesis of LLOs starting from a mixture of the precursor and lithium source(Li2CO3).It is the original formation mechanism of LLOs that inspires to develop a promising and practical method, a coprecipitation route followed by a microwave heating process, for controllable synthesis of the layered monoclinic Li[Li$_{0.2}$Ni$_{0.2}$Mn$_{0.6}$]O$_2$ cathode materials with high rate performance(i.e. a specific discharge capacity of 171 mAh g$^{-1}$ at 10 C). An increased oxidation of transition metal cations during high-temperature lithium insertion process reveals that oxygen atoms are continuously inserted into the host structure to keep charge neutrality and provide the open coordination sites for incorporated lithium ions and relocatedTM ions during preparation of LLOs. Thehigh-temperature lithiation reaction is accompanied by phase transition, atomic rearrangement,and surface reconstruction. Despite the fact that the synthesized monoclinic Li[Li$_{0.2}$Ni$_{0.2}$Mn$_{0.6}$]O$_2$ cathode could deliver a good rate performance,itsuffers froma serious voltage decay during electrochemicalcycling. Therefore, in situhigh-resolution SRD was carried out in order to understand the structural evolutionof the Li-excess layered electrode during electrochemical cyclingand to figure out what are the important factors responsible for the degradationof LLOs. The in situSRD results suggestthat the nanodomain formation of a layered phase and a spinel-like phase after charging to high voltages (above 4.5 V)is the main contributing factor forthe structural instability.The fatigue crack in the electrode material after prolonged cycling is directly observedby high-resolution transmission electron microscopy(HRTEM),which is ascribed tothe volume variation induced by anisotropic lattice strain during the delithiation/lithiation process.Tobetter understandthe relationshipbetween the formation mechanism and degradation mechanism of LLOs, a series of LixNi$_{0.2}$Mn$_{0.6}$ Oyoxideswith a large variety of providedlithiumcontents (0.00$≤ x ≤$1.52) wasprepared via a thermal treatment. The consistent resultsdemonstrate that the structural properties of Li$_x$Ni$_{0.2}$Mn$_{0.6}$Oyoxides are strongly dependent on the chemical composition with respect tolithium and oxygen.The Li-excess layered Li[Li$_{0.2}$Ni$_{0.2}$Mn$_{0.6}$]O$_2$ oxide is only stable when a considerable amount of lithium and oxygen isavailableduring synthesis, while at a lower concentration of them, the spinel/rock-salt-typephase is thermally stable. These findings offer new insights into the nature of fatigue processesin LLOs.Due to factthat the competition between thermally-induced oxygen loss and lithium-insertion-induced oxygen uptake occurs, the high-temperature reaction of the precursor and lithium source gets much more complicated. Lastly, in situ high-temperature SRD technique wasutilized to explore the chemically (i.e. Li & O) induced structural evolution for the pure spinel oxide (Fd$\bar{3}$m), so as to provide a guarantee of reliable lithiation reaction mechanism with oxygen uptake. The original formation mechanism of Li-containing oxidesindicatesthat the Li-excess layered oxides can be formed as a result of lithium and oxygen insertion into the spinel (Fd$\bar{3}$m) and/or Li-containing rock-salt-typephase (Fm3̅m)during synthesisat air atmosphere. Ifa smallamountoflithium is provided, lithium atoms have a tendency to be located on tetrahedral positions, forming the Li-containing spinel oxides. As more lithium ionsare graduallyincorporated into the spinel matrix, lithium atomstend to preferentially occupythe octahedral sites forming Li-containing rock-salt-typephase and/or Li-rich layered phase. Because the oxygen anion cubic close-packed latticeis involved during phase transformation, oxygen atomsare supposed to be inserted onlyintothe oxygenlattice at the surface, associated withcrystal growth and/or recrystallization. These discoveries not only contribute toa comprehensive understanding of the correlation between preparation, structure and performance for next-generation LIBs, but also provide new insights into the interaction of oxygen with lithium in Li-containing oxides during synthesis and electrochemical cycling.