熔石英表面缺陷的超快荧光及激光损伤关联关系

计算机科学 末端学 人工智能 易熔合金 变质岩石学 医学 材料科学 自然(考古学) 物理 城市环境
作者
刘钰波 Liu Yubo,王狮凌 Wang Shiling,郑剑锋 Zheng Jianfeng,王泽栋 Wang Zedong,李溪远 Li Xiyuan,吴兰 Wu Lan,刘崇 Liu Chong,刘东 Liu Dong
出处
期刊:Guangxue xuebao [Shanghai Institute of Optics and Fine Mechanics]
卷期号:45 (21): 2122001-2122001 被引量:1
标识
DOI:10.3788/aos250907
摘要

Objective Fused silica optical components are widely used in high-energy, high-power laser devices such as inertial confinement fusion and laser weapons due to their excellent optical transmittance and uniformity. However, surface defects, including scratches, pits, and cracks, are inevitably generated during the processing of optical components. These surface defects can induce damage under the irradiation of high-power ultraviolet laser pulses, reducing the laser-induced damage threshold (LIDT) of the components. This has become one of the key factors limiting the output power of high-power laser devices and the service life of optical systems. However, there is a lack of an intuitive quantitative relationship between the evaluation parameters of surface defects and damage performance, which restricts the effective evaluation of surface defect damage performance and further improvement of damage resistance of components. In recent years, fluorescence detection technology has evolved into an effective means of defect characterization, which can reflect the damage characteristics of fused silica components to a certain extent. In this paper, based on the confocal time-resolved photoluminescence microscopy (CTPM) technique, we observe the artificial indentations on the surface of fused silica optical components to obtain two-dimensional images of the fluorescence intensity and lifetime. Subsequently, the samples are subjected to R-on-1 laser damage performance tests to study the specific correlation between the fluorescence characteristics of surface defects and their damage characteristics. Methods In this paper, artificial indentations are fabricated on the surface of fused silica elements, and their ultrafast fluorescence characteristics are measured. Subsequently, laser damage tests are conducted on the indentations to investigate the relationship between the ultrafast fluorescence characteristics of different defect structures and laser damage resistance. Artificial indentations are used to simulate surface and subsurface defects generated during the processing, and a series of indentations are prepared using a Vickers hardness tester. The surface defect fluorescence characteristics testing system based on CTPM uses time-correlated single photon counting (TCSPC) technology to measure fluorescence intensity and fluorescence lifetime. By recording the arrival time of the first fluorescence photon after each excitation pulse and accumulating these events over multiple repetitions a photon number-time histogram proportional to the fluorescence decay curve is established through multiple repetitions. The fluorescence intensity of the sampling point is obtained by summing the photon counts of each time channel, and the fluorescence lifetime characteristic value of the sampling point is obtained by fitting the curve with a stretched exponential model. Two-dimensional images of surface defect fluorescence intensity and lifetime are obtained by galvanometer scanning. After completing the fluorescence measurement of the indentations, the indentations are exposed to several ultraviolet (UV) nanosecond laser pulses for testing. The damage performance of the indentation is tested using the R-on-1 method, with multiple laser pulses irradiating each indentation, and the energy density of each pulse is increased compared to the previous one until initial damage occurs to the indentation. Results and Discussions Experimental results show that for indentations produced with larger loads on the surface of fused silica, the ultrafast fluorescence is mainly distributed in the following three types of defect characteristic structures: the crushed area at the indentation edge, the radial cracks, and the larger area of fracture and crushing at the indentation center. For indentations produced with smaller loads on the surface of fused silica, the ultrafast fluorescence is mainly distributed in the deformation area at the indentation edge. The damage test results show that areas with higher fluorescence intensity and shorter fluorescence lifetime are more prone to damage. For the brittle structures of surface defects in fused silica, the fluorescence lifetime is shorter and the defect density is higher. At the same time, higher fluorescence intensity indicates a higher electron density and stronger laser absorption at that location. Therefore, locations with higher fluorescence intensity and shorter fluorescence lifetime are more likely to absorb intense laser light and undergo damage. To quantitatively analyze the relationship between indentation damage threshold and fluorescence intensity, the fluorescence intensity at the damage locations of multiple indentations and their damage thresholds are statistically analyzed. The results show that the damage threshold decreases logarithmically with increasing fluorescence intensity. Conclusions In this paper, a surface defect fluorescence testing system based on CTPM is used to obtain images of fluorescence intensity and fluorescence lifetime of fused silica surface indentations. For brittle structures such as fractures and cracks, the fluorescence intensity is greater and the lifetime is shorter, indicating that these locations have a higher defect density and stronger laser absorption. Subsequently, laser damage tests are conducted on the indentations. The experimental results show that locations with higher fluorescence intensity and shorter fluorescence lifetime are more likely to absorb intense laser light and undergo damage. The fluorescence distribution is closely related to the locations where damage occurs. Statistical results indicate that the damage threshold decreases logarithmically with increasing fluorescence intensity. Therefore, ultrafast fluorescence can, to some extent, non-destructively characterize damage precursors and predict the laser damage performance of surface defects in fused silica.
最长约 10秒,即可获得该文献文件

科研通智能强力驱动
Strongly Powered by AbleSci AI
科研通是完全免费的文献互助平台,具备全网最快的应助速度,最高的求助完成率。 对每一个文献求助,科研通都将尽心尽力,给求助人一个满意的交代。
实时播报
1秒前
qiuxuan100完成签到,获得积分10
1秒前
2秒前
无花果的应助被俭朴的明轩采纳,获得10
3秒前
小二郎的应助被Wrx采纳,获得10
3秒前
3秒前
3秒前
田様的应助被YYT采纳,获得10
3秒前
zhugepengju发布了新的文献求助10
3秒前
慕青的应助被wdqa采纳,获得10
4秒前
wyx1103完成签到,获得积分10
4秒前
4秒前
竹夕完成签到 ,获得积分10
5秒前
Li发布了新的文献求助10
5秒前
gsj完成签到,获得积分10
5秒前
maT发布了新的文献求助10
6秒前
开朗含海完成签到,获得积分10
6秒前
苗觉觉完成签到,获得积分10
6秒前
6秒前
JM发布了新的文献求助10
7秒前
王12完成签到,获得积分10
8秒前
学不动了发布了新的文献求助10
9秒前
10秒前
zzz完成签到,获得积分10
10秒前
时平谊发布了新的文献求助10
11秒前
11秒前
开朗含海发布了新的文献求助10
11秒前
海鲜面发布了新的文献求助10
12秒前
寒冷凌寒完成签到 ,获得积分10
12秒前
真实的麦片完成签到,获得积分10
14秒前
14秒前
14秒前
15秒前
16秒前
17秒前
17秒前
17秒前
17秒前
ui24发布了新的文献求助10
17秒前
zachary完成签到,获得积分10
18秒前
高分求助中
(应助此贴封号)【重要!!请各用户(尤其是新用户)详细阅读】【科研通的精品贴汇总】 10000
拉伸高分子熔体中缠结行为的模拟和小角中子散射研究 1700
Grapes 1000
The World Atlas of Wine 9th edition 1000
奈特基础组织学:配套组织病理学(第4版)(Netter's Essential Histology With Correlated Histopathology) 800
John McDowells Bildungstheorie 800
八旗制度の研究 600
热门求助领域 (近24小时)
化学 材料科学 医学 生物 纳米技术 计算机科学 工程类 有机化学 化学工程 生物化学 物理 复合材料 内科学 催化作用 光电子学 人工智能 细胞生物学 无机化学 物理化学 数学
热门帖子
关注 科研通微信公众号,转发送积分 8178807
求助须知:如何正确求助?哪些是违规求助? 9569558
关于积分的说明 21805222
捐赠科研通 7773974
什么是DOI,文献DOI怎么找? 3432933
关于科研通互助平台的介绍 2556873
邀请新用户注册赠送积分活动 2478593