Liquid-Phase Synthesis of High Lithium-Ion Conducting Li6PS5Br Solid Electrolyte Using Ethanol and Its Application to All-Solid-State Lithium Secondary Batteries

All-solid-state lithium secondary batteries using nonflammable inorganic solid electrolytes have been expected as next-generation batteries with greater safety and reliability. In order to improve the electrochemical properties of the all-solid-state batteries, the studies on sulfide-based solid electrolytes with high ionic conductivities and favorable mechanical properties have been actively carried out. Especially, argyrodite-type Li 6 PS 5 X (X=Cl, Br) crystals are attracting much attention as sulfide-based solid electrolytes with a high lithium-ion conductivities of more than 10 -3 S cm -1 at room temperature [1]. In general, it is difficult to prepare solid-solid interfaces between electrodes and solid electrolytes with large contact areas in bulk-type all-solid-state batteries. In order to form favorable interfaces, a coating of active material particles with solid electrolytes is an effective process. We have reported that LiCoO 2 (LCO) particles were coated with Li 2 S-P 2 S 5 solid electrolytes by the pulsed laser deposition (PLD) method and the all-solid-state batteries using electrolyte-coated LCO showed the higher capacities than those using non-coated LCO [2]. Liquid-phase methods are simpler and more cost-effective than the gas-phase methods such as PLD. We have reported that Li 2 S-P 2 S 5 solid electrolytes were synthesized using N -methylformamide (NMF) via homogeneous solution from starting materials [3]. Moreover, the sulfide solution was used for the formation of interfaces between LCO and Li 2 S-P 2 S 5 solid electrolytes with the large contact areas in all-solid-state batteries. However, the prepared electrolyte showed a low ionic conductivity of 2.3×10 -6 S cm -1 at room temperature. Recently, we have reported that argyrodite-type Li 6 PS 5 X (X=Cl, Br) solid electrolyte prepared by mechanical milling was dissolved in ethanol solution, and the ionic conductivity of the reprecipitated electrolyte was 10 -5 -10 -4 S cm -1 at room temperature [4]. Moreover, all-solid-state batteries using Li 6 PS 5 Br-coated LCO prepared using this process showed the same capacities as the batteries using LCO coated with Li 2 S-P 2 S 5 solid electrolytes by PLD. However, this approach needs the multi-step processes of mechanical milling and dissolution-reprecipitation. In this study, the Li 6 PS 5 Br solid electrolyte was synthesized from Li 2 S, LiBr and Li 3 PS 4 by liquid-phase reaction using ethanol. In addition, Li 6 PS 5 Br solid electrolyte was coated on LiNi 1/3 Mn 1/3 Co 1/3 O 2 particles (Li 6 PS 5 Br-coated NMC) using ethanol solution and then the all-solid-state batteries using Li 6 PS 5 Br-coated NMC were fabricated and characterized. Li 2 S and LiBr as the starting materials were completely dissolved into dehydrated ethanol and then Li 3 PS 4 glass were added into the solution. The solution was dried at 150 o C under vacuum to obtain solid powders. On the other hand, NMC particles were coated with Li 6 PS 5 Br solid electrolyte using the obtained ethanol solution. The all-solid-state batteries using the mixture of NMC and Li 6 PS 5 Br powders or only Li 6 PS 5 Br-coated NMC were fabricated and characterized. The weight ratios of NMC to Li 6 PS 5 Br solid electrolyte were 90/10. The homogeneous solution was prepared by dissolution of Li 2 S, LiBr and Li 3 PS 4 glass into ethanol. The white powder was obtained after removing ethanol by drying at 150 o C under vacuum. X-ray diffraction (XRD) measurements and Raman spectroscopy suggested that the obtained powder was mainly Li 6 PS 5 Br crystal. Ionic conductivity of the Li 6 PS 5 Br solid electrolyte at room temperature was 1.9×10 -4 S cm -1 and the activation energy for conduction was 34 kJ mol -1 . Li 6 PS 5 Br-coated NMC was prepared by mixing the ethanol solution and NMC particles and subsequent removing the solvent. Scanning electron microscopy (SEM) image and energy dispersive X-ray analysis (EDX) mapping of Li 6 PS 5 Br-coated NMC indicated that Li 6 PS 5 Br coating layer on NMC was formed with the large contact areas. The all-solid-state batteries using only Li 6 PS 5 Br-coated NMC showed the reversible capacity of about 120 mAh g -1 , although the batteries using the mixture of NMC and Li 6 PS 5 Br powders showed the reversible capacity of about 75 mAh g -1 . References [1] R.P. Rao et al ., Phys. Status Solidi A , 8 (2011) 1804. [2] A. Sakuda et al ., J. Am. Ceram. Soc ., 93 (2010) 765. [3] S. Teragawa et al ., J. Mater. Chem. A , 2 (2014) 5095. [4] S. Yubuchi et al ., J. Powder Sources , 293 (2015) 941. Acknowledgement This research was financially supported by the Japan Science and Technology Agency (JST), “Advanced Low Carbon Technology Research and Development Program, Specially Promoted Research for Innovative Next Generation Batteries program (ALCA-SPRING)”.