Optimization of Cu2ZnSnS4 Absorber Layers via Sulfurization of Electrodeposited Cu-Zn-Sn Precursors for Photovoltaic Applications

作者
Begüm Ünveroğlu
标识
DOI:10.18130/v3hf3k
摘要

Solar cells based on thin film absorbers provide an inexpensive and versatile technology to directly convert solar energy to electricity. Recent manufacturing developments have led to a significant decrease in the cost of solar energy, which has recently become lower than that of electricity from the grid, thus making this renewable energy option much more attractive. Kesterite solar cells comprised of a Cu2ZnSnS4 (CZTS) absorber layer are unique among thin film solar cell architectures since they are made up of earth-abundant, non-toxic elements, potentially enabling a widespread adoption of this technology, in contrast to current CdTe or Cu(In,Ga)Se2 which contain toxic elements. Unfortunately, CdTe and Cu(In,Ga)Se2 achieve efficiencies above 20%, while the record efficiency of thin film solar cells based on CZTS absorber films is only 12%. A simple, inexpensive, and scalable method for growing CZTS absorbers is electrodeposition of Cu-Zn-Sn metallic precursor and sulfurization method; so far CZTS grown with this method however is still only around 5%, and the origin of this limitation is not understood. On the basis of this knowledge gap, this dissertation investigates in detail the electrochemical synthesis and characterization of CZTS absorber layers with the aim to achieve a highly uniform, single phase material with a high conversion efficiency and good stability. Electrodeposition of Cu-Zn-Sn (CZT) films followed by vapor phase sulfurization is an environmentally friendly and practical method to grow kesterite Cu2ZnSnS4 (CZTS) absorber layers on Mo substrates. In this work we discuss the influence of CZT alloy composition, its compositional spread, and sulfurization parameters on the formation of secondary phases and structural inhomogeneity, which negatively affect the performance of CZTS layers. The stoichiometric composition for Cu2ZnSnS4 is Cu: 25 at%, Zn: 12.5 at%, Sn: 12.5 % and S: 50 at%, however slightly off stoichiometric Zn-rich and Cu-poor CZTS films have been reported to give higher efficiency than the stoichiometric ones. The compositional ratios that best correlate with performance in CZTS materials are the Zn/Sn and Cu/(Zn+Sn) ratio. Zn-rich films have Zn/Sn > 1.0 ratio and Cu-rich films have Cu/(Zn+Sn) < 1 ratio. Therefore, in our studies we target Zn-rich and Cu-poor CZTS films and for this purpose, we deposited Cu-poor CZT metallic precursors with different Zn/Sn ratios before sulfurization of the layers. Electrodeposition of CZT was carried out using two distinct chemistries: an acidic citrate solution and an alkaline pyrophosphate solution. The main difference between these two electrolytes was the reduction potential of zinc, which was deposited only after the hydrogen evolution reaction, significantly influencing the morphology of the CZT metallic precursors. In addition, the alkaline solution contained potassium, which acted as a growth modifier during the growth of CZTS films, increasing the size of the grains. CZT alloys obtained from the acidic electrolyte were sulfurized at various temperatures and the influence of Zn/Sn ratio of the resulting CZTS layers on the film quality was studied. We found that Zn-rich (27-29%) and Cu-poor (47-49 at %) CZT metallic precursors formed fewer amounts of secondary phases and showed better crystallinity after sulfurization. Furthermore, CZTS layers with a higher Zn/Sn ratio showed improved photoelectrochemical (pec) response, up to 0.5 mA/cm2 and 0.99 mA/cm2 for sulfurization temperatures of 500 °C and 550 °C, respectively. The photoelectrochemical response was correlated to the phase purity and crystallinity of the CZTS, as determined from XRD and Raman Spectroscopy analyses. In order to understand the influence of the electrodeposition current distribution on the standard deviation of the alloy composition, we deposited the CZT metallic precursors with a basic electrolyte, using vertical and horizontal deposition experimental set ups; the latter configuration avoided natural convection and thus enhanced flow uniformity. The compositional standard deviation of CZT metallic precursors did indeed decrease by using the horizontal deposition set up, and higher pec response was observed owing to the improved phase purity of the CZTS layers, as seen from compositional mapping of the films. Despite the improved uniformity however, the highest pec response (0.4 mA/cm2) of CZTS films from the basic solution was lower than that of CZTS films grown from an acidic solution. Even though Raman spectra results showed similar crystallographic properties at the surface of the CZTS layers, XRD analyses suggested the presence of slightly more secondary phases for the bulk of the CZTS layers grown from the alkaline solution in comparison to the acidic solution, which was found to be the reason for lower pec performance. In a parallel effort, we deposited CZT metallic precursors with the addition of small amounts of bismuth (< 1 at%, CZT-Bi) from an acidic citrate solution to investigate the dopant role of bismuth and its influence on the performance of CZTS based materials. These films showed the highest pec, 2.65 mA/cm2, with the optimum amount of Bi (~0.5 at%) in Zn-rich CZTS layers. The increased pec response was attributed to the enhanced growth of the CZTS grains and improved phase purity with respect to CZTS films without any dopant addition. Even though reasonably good pec responses were obtained with CZTS based films, the solar cell efficiency of the CZTS layers was less than 1%. The highest solar cell efficiency was 0.64% for CZTS films formed via sulfurization of CZT precursors grown from the acidic electrolyte. We found that the solar cell performance was compromised in presence of secondary phases, particularly the conductive phase CuxSy , which lowered the short circuit current by acting as a shunt path. Time resolved photoluminescence and measurements of the external quantum efficiency also suggested the presence of a high density of recombination centers, which lowered the open circuit voltage, hence the efficiency of the CZTS based cells. Various possible solutions towards improved material and higher performance are also outlined.

科研通智能强力驱动
Strongly Powered by AbleSci AI
科研通是完全免费的文献互助平台,具备全网最快的应助速度,最高的求助完成率。 对每一个文献求助,科研通都将尽心尽力,给求助人一个满意的交代。
实时播报
1秒前
1秒前
徐香猕猴桃完成签到 ,获得积分10
1秒前
qducly2026的应助被四号玩家采纳,获得50
2秒前
2秒前
2秒前
能干戎完成签到,获得积分10
2秒前
猕猴桃完成签到 ,获得积分10
2秒前
jzt12138发布了新的文献求助10
3秒前
cx发布了新的文献求助30
3秒前
迷路荷花发布了新的文献求助10
3秒前
慕青的应助被Zzzj采纳,获得10
4秒前
4秒前
lit完成签到,获得积分10
4秒前
上课呢发布了新的文献求助10
5秒前
秋风的应助被是袁三岁采纳,获得10
5秒前
wang发布了新的文献求助10
6秒前
余香的应助被风韵犹存采纳,获得10
6秒前
英俊的铭的应助被白马非马jmh采纳,获得10
6秒前
leaf发布了新的文献求助10
6秒前
7秒前
8秒前
Jasper的应助被molurenjvb采纳,获得10
8秒前
9秒前
小薯条发布了新的文献求助10
9秒前
目移完成签到,获得积分10
9秒前
传奇3的应助被糖醋里脊加醋采纳,获得10
9秒前
9秒前
Nole的应助被211107采纳,获得10
10秒前
完美世界的应助被211107采纳,获得30
10秒前
10秒前
10秒前
11秒前
11秒前
12秒前
禾斗完成签到,获得积分10
12秒前
英吉利25发布了新的文献求助10
12秒前
12秒前
stccc完成签到 ,获得积分10
13秒前
Lucas的应助被milai采纳,获得10
13秒前
高分求助中
(应助此贴封号)【重要!!请各用户(尤其是新用户)详细阅读】【科研通的精品贴汇总】 10000
拉伸高分子熔体中缠结行为的模拟和小角中子散射研究 1700
The World Atlas of Wine 9th edition 1000
奈特基础组织学:配套组织病理学(第4版)(Netter's Essential Histology With Correlated Histopathology) 800
John McDowells Bildungstheorie 800
八旗制度の研究 600
What Else Can I Tell You?: A Pragmatic Study of English Rhetorical Questions as Discursive and Argumentative Acts 500
热门求助领域 (近24小时)
化学 材料科学 医学 生物 纳米技术 计算机科学 工程类 有机化学 化学工程 生物化学 物理 复合材料 内科学 催化作用 光电子学 人工智能 细胞生物学 无机化学 物理化学 数学
热门帖子
关注 科研通微信公众号,转发送积分 8163664
求助须知:如何正确求助?哪些是违规求助? 9557817
关于积分的说明 21741980
捐赠科研通 7754358
什么是DOI,文献DOI怎么找? 3428338
关于科研通互助平台的介绍 2553000
邀请新用户注册赠送积分活动 2472943