作者
Riena Jinno,Takayuki Uchida,Kentaro Kaneko,Shizυo Fujita
摘要
These days, huge attention has been given to power devices using wide bandgap semiconductors, which can lead to energy-saving. We have taken interest in corundum-structured Ga 2 O 3 (α-Ga 2 O 3 ) having wider bandgap compared with those of SiC and GaN, because it is considered to have much higher endurance voltage and lower on-resistance [1]. By using mist CVD [2], which is a safe, cost-effective, and environmental-friendly growth technology, Sn-doped α-Ga 2 O 3 thin films grown on sapphire substrates showed n-type conductivity with Hall mobility of ~20 cm 2 /Vs and carrier concentration of about 10 19 cm -3 ,but the mobility markedly decreases when the carrier concentration was controlled at the range of 10 17 cm -3 [3]. Because of the large lattice mismatch between α-Ga 2 O 3 and sapphire (4.8 and 3.5% for a- and c-axes), α-Ga 2 O 3 thin films grown on sapphire substrates contain a high dislocation density. Especially edge dislocation density was measured as 7×10 10 cm -2 [4], which seems to deteriorate carrier conduction in the α-Ga 2 O 3 layer. It is considered that dislocations trap free electrons and are negatively charged, diminishing the electron mobility due to electron scattering. Aiming at decreasing the dislocation density in α-Ga 2 O 3 thin films and improving the electrical properties, in this study we report the fabrication of the α-Ga 2 O 3 using α-(Al x Ga 1- x ) 2 O 3 multilayers as a buffer layer overcoming the lattice mismatch between α-Ga 2 O 3 and sapphire. The α-Ga 2 O 3 main layer and the α-(Al x Ga 1- x ) 2 O 3 buffer layers were grown on c-plane sapphire substrate by the mist CVD method. Prior to the growth, a sapphire substrate was annealed in air at 1050 o C for 12 hours to form atomically flat and clean surface. The buffer layer consists with 12 pairs of 20-nm thick α-(Al 0.9 Ga 0.1 ) 2 O 3 /α-(Al 0.2 Ga 0.8 ) 2 O 3 multilayer structure. The thickness ratios for α-(Al 0.9 Ga 0.1 ) 2 O 3 /α-(Al 0.2 Ga 0.8 ) 2 O 3 were gradually changed from 1 (on sapphire) to 0.09 (top of the buffer layer) so that the average composition of the buffer layer changed from Al-rich (close to sapphire) to Ga-rich (close to Ga 2 O 3 ). Then, a 150-nm thick α-(Al 0.2 Ga 0.8 ) 2 O 3 layer was grown on the 12 pairs of α-(Al 0.9 Ga 0.1 ) 2 O 3 /α-(Al 0.2 Ga 0.8 ) 2 O 3 layers, followed by the growth of a 150-nm thick α-Ga 2 O 3 main layer. The growth of α-Ga 2 O 3 and α-(Al x Ga 1- x ) 2 O 3 layers were carried out at 470 and 700 o C, respectively. From the reciprocal space map for (11-29) reflection, we attributed the three intense reflection patterns originating from the sapphire substrate, the thick α-(Al 0.2 Ga 0.8 ) 2 O 3 layer on the buffer layer (below the α-Ga 2 O 3 main layer), and the α-Ga 2 O 3 main layer. The α-Ga 2 O 3 and α-(Al 0.2 Ga 0.8 ) 2 O 3 layers are lattice-relaxed with respect to the sapphire substrate and the α-Ga 2 O 3 layer seems to be subject to slight in-plane compressive strain. The cross-sectional transmission electron microscope (TEM) image of the sample observed along the <11-20> zone axis shows that the sample structure consisting with periodic multilayers of α-(Al 0.9 Ga 0.1 ) 2 O 3 and α-(Al 0.2 Ga 0.8 ) 2 O 3 is actually fabricated. The thickness of a unit pair of α-(Al 0.9 Ga 0.1 ) 2 O 3 /α-(Al 0.2 Ga 0.8 ) 2 O 3 was recognized as about 20 nm, which was nearly the same as designed. Cross-sectional TEM images under two-beam conditions were obtained to discuss the dislocation structure of the buffer layers and the α-Ga 2 O 3 main layer. These images reveal that most of the strains are concentrated in the α-(Al x Ga 1-x ) 2 O 3 buffer layers. The densities of screw and edge dislocations in the α-Ga 2 O 3 thin film were approximated as 3×10 8 and 6×10 8 cm -2 , respectively. By introducing the buffer layers, the edge dislocations in the α-Ga 2 O 3 thin films was successfully reduced from 7×10 10 cm -2 (in a α-Ga 2 O 3 thin film directly grown on a sapphire substrate) to 6×10 8 cm -2 by more than two order of magnitude. By optimizing the structure and growth conditions of the buffer layers, the further improvements in quality of the α-Ga 2 O 3 main layer is expected, leading to attractive device performance using inexpensive and large-area sapphire substrates. References [1] S. Fujita, Jpn. J. Appl. Phys. 82 (2013) 836. [2] D.Shinohara, et al ., Jpn. J. Appl. Phys, 47 (2008)7311. [3] K. Akaiwa: Dr.Thesis, Department of Electronic Science and Engineering, Kyoto University, Kyoto, 2016. [4] K.Kaneko, et.al ., Jpn. J. Appl. Phys, 51 (2012) 020201.