激光合金化改性8YSZ热障涂层的抗热腐蚀性能研究

材料科学
作者
孙磊 Sun Lei,郭雨嘉 Guo Yujia,张盼盼 Zhang Panpan,刘蓉 Liu Rong,Qunli Zhang,姚建华 Yao Jianhua
出处
期刊:Zhongguo jiguang [Science Press]
卷期号:50 (4): 0402002-0402002 被引量:3
标识
DOI:10.3788/cjl220433
摘要

Objective Thermal barrier coatings can protect hot end components from high temperature, high pressure, and high stresses, which are extensively applied in gas turbine engine blades, combustion chamber, and ducting and nozzle guide vanes. However, many impurities (sodium, sulfur) exist in the operating gases and fuels, condensation of which leads to the formation of molten corrosive salts during the long-time service process, which may lead to the serious hot corrosion failure and reduce the lifetime of thermal barrier coatings. Plasma-sprayed thermal barrier coatings possess the typical characteristic of pores and laminar structure, which may provide penetration paths for molten corrosive salts into the coating. To improve the hot corrosion resistance, it is necessary to produce a denser layer to prevent molten salts from penetrating into porous coatings. Laser alloying technology has the advantages of high energy density, short action time, and reliable processing quality, and thus can change the loose porous structure of the plasma-sprayed thermal barrier coatings. Meanwhile, the oxidation reaction of self-healing materials at high temperature can produce some oxidation products, which can further fill the pores and cracks in the porous coatings. Therefore, the combination of laser alloying technology and self-healing materials is an alternative method to improve the hot corrosion resistance of thermal barrier coatings, which is few reported. The purpose of this paper is to study the effect of laser alloying on the microstructure, phase composition, and hot corrosion properties of thermal barrier coatings. Methods In this study, the double-layer thermal barrier coatings of NiCrAlY/8YSZ were deposited onto superalloy substrate via air plasma spraying. The mixture powders of TiAl3 particles with 10% mass fraction and Ceria and Yttria-stabilized Zirconia (CYSZ) ceramic were pre-placed on the plasma-sprayed thermal barrier coatings, and then processed using a fiber-coupled semiconductor laser. The mixture of 25% NaCl and 75% Na2SO4 as the corrosive salts was spread on the surface of the plasma-sprayed and laser-alloyed thermal barrier coatings with deposition content of 10 mg/cm2. The hot corrosion test was conducted in a furnace at 900 ℃ for 4 h. Finally, the microstructure, phase composition and hot corrosion behaviors of the plasma-sprayed and laser-alloyed thermal barrier coatings were systematically investigated. Results and Discussions After the laser alloying treatment, the porous and laminar microstructures in the plasma-sprayed thermal barrier coatings were eliminated. As a result, dense columnar crystal structure and some segmented microcracks were formed in the laser-alloyed thermal barrier coatings (Fig. 2). The detrimental monoclinic zirconia (m-ZrO2) disappears after the air plasma spraying and the laser alloying treatment, and all phases in the 8YSZ powder turn to non-equilibrium tetragonal zirconia (t'-ZrO2) and cubic zirconia (c-ZrO2) (Fig. 3). Because of the rapid cooling and solidification rate of air plasma spraying and laser alloying treatment, the phase transformation of t'-ZrO2 to m-ZrO2 is restrained. After the hot corrosion at 900 ℃ for 4 h in molten salts (25% NaCl+75% Na2SO4), the corrosion products of Y2(SO4)3 and m-ZrO2 were found in the plasma-sprayed thermal barrier coatings, and Y2(SO4)3 and Al2O3 were detected in the laser-alloyed thermal barrier coatings [Figs. 5(a) and (b)]. Compared with the plasma-sprayed thermal barrier coatings, there are less corrosion products on the surface of the laser-alloyed thermal barrier coatings [Fig. 4(b) and Fig. 6(b)]. Therefore, the hot corrosion resistance of the laser-alloyed thermal barrier coatings is superior to that of the plasma-sprayed thermal barrier coatings. On the one hand, the dense columnar structure in the laser-alloyed thermal barrier coatings can inhibit the penetration of molten salts; on the other hand, the self-healing agent TiAl3 undergoes oxidation reaction at high temperature, and the formed Al2O3 and a small amount of TiO2 can fill the cracks, which can further reduce the hot corrosion reaction between molten salts and yttria stabilizer [Figs. 9(c), (d), and (e)]. Conclusions In this study, a typical double-layer 8YSZ/NiCrAlY thermal barrier coating was prepared via air plasma spraying technology, and then the self-healing agent TiAl3 was introduced into the thermal barrier coatings through laser alloying technology. Microstructure, phase composition, and hot corrosion properties of the plasma-sprayed and the laser-alloyed thermal barrier coatings were investigated. The surface of the plasma-sprayed thermal barrier coatings is relatively rough, and there are many microcracks and pores within it. While the surface of the laser-alloyed thermal barrier coatings is smooth, and some fine segmented microcracks and dense columnar crystals are formed. After the hot corrosion in the 25% NaCl+75% Na2SO4 molten salt at 900 ℃ for 4 h, it was found that there were corrosion products Y2(SO4)3 and harmful m-ZrO2 in the plasma-sprayed and the laser-alloyed thermal barrier coatings; however, less corrosion products existed in the latter. The hot corrosion resistance of the laser-alloyed thermal barrier coatings is much better than that of the plasma-sprayed thermal barrier coatings. On the one hand, the oxidation reaction of self-healing agent TiAl3 during the process of high-temperature hot corrosion produces Al2O3 and less TiO2, and they can fill some cracks in the coating and reduce the penetration paths of the corrosion salts. On the other hand, the laser-alloyed layer with dense columnar structure can inhibit the penetration of molten salt and reduce the occurrence of thermal corrosion reaction. Finally, the hot corrosion resistance of laser-alloyed thermal barrier coatings is greatly improved.
最长约 10秒,即可获得该文献文件

科研通智能强力驱动
Strongly Powered by AbleSci AI
科研通是完全免费的文献互助平台,具备全网最快的应助速度,最高的求助完成率。 对每一个文献求助,科研通都将尽心尽力,给求助人一个满意的交代。
实时播报
zoeeeeee发布了新的文献求助10
1秒前
汉堡包的应助被DW采纳,获得30
1秒前
Ss完成签到,获得积分10
2秒前
ding发布了新的文献求助30
2秒前
Metx完成签到 ,获得积分10
2秒前
饼大王发布了新的文献求助10
2秒前
3秒前
ohh完成签到 ,获得积分10
4秒前
无极微光的应助被吕大本事采纳,获得20
5秒前
搜集达人的应助被这题不讲采纳,获得10
6秒前
乌贼爱吃完成签到,获得积分10
7秒前
科研通AI65的应助被linn采纳,获得10
9秒前
11秒前
爆米花的应助被DW采纳,获得10
12秒前
风中的眼神完成签到,获得积分10
12秒前
12秒前
12秒前
maguodrgon发布了新的文献求助10
13秒前
14秒前
15秒前
16秒前
17秒前
猪猪侠在读研完成签到,获得积分10
17秒前
聪明笨蛋发布了新的文献求助10
17秒前
倩倩发布了新的文献求助10
18秒前
Xiao发布了新的文献求助10
20秒前
希望天下0贩的0的应助被Co采纳,获得30
21秒前
xixi发布了新的文献求助10
21秒前
22秒前
FashionBoy的应助被伶俐的不评采纳,获得10
22秒前
Orange的应助被留无影采纳,获得30
22秒前
烦人糕糕完成签到,获得积分10
22秒前
无花果的应助被伶俐的不评采纳,获得10
22秒前
秋风的应助被伶俐的不评采纳,获得10
22秒前
共享精神的应助被AA采纳,获得10
23秒前
23秒前
23秒前
orixero的应助被伶俐的不评采纳,获得10
23秒前
Nole的应助被伶俐的不评采纳,获得10
23秒前
充电宝的应助被伶俐的不评采纳,获得10
23秒前
高分求助中
(应助此贴封号)【重要!!请各用户(尤其是新用户)详细阅读】【科研通的精品贴汇总】 10000
拉伸高分子熔体中缠结行为的模拟和小角中子散射研究 1700
The World Atlas of Wine 9th edition 1000
Sex, Aging, and Death in a Medieval Medical Compendium: Trinity College Cambridge MS R.14.52, Its Texts, Language, and Scribe 500
高分子基功能界面水蒸发材料与应用研究 500
外场增强的水汽发电研究 500
基于结构调控的功能化水诱导发电材料与器件研究 500
热门求助领域 (近24小时)
化学 材料科学 医学 生物 纳米技术 计算机科学 工程类 有机化学 化学工程 生物化学 物理 复合材料 内科学 催化作用 光电子学 人工智能 细胞生物学 无机化学 物理化学 数学
热门帖子
关注 科研通微信公众号,转发送积分 8188295
求助须知:如何正确求助?哪些是违规求助? 9576112
关于积分的说明 21845392
捐赠科研通 7786320
什么是DOI,文献DOI怎么找? 3435276
关于科研通互助平台的介绍 2559581
邀请新用户注册赠送积分活动 2482182