作者
Tomomi Sawada,Toshihide Nabatame,Takashi Onaya,Mari Inoue,Akihiko Ohi,Naoki Ikeda,Kazuhito Tsukagoshi
摘要
Several stack structures such as 1 st ZrO 2 /Al 2 O 3 /2 nd ZrO 2 (ZAZ), 1 st TiO 2 /Al 2 O 3 /2 nd TiO 2 (TAT), and 1 st ZrO 2 /(Ta/Nb)O x -Al 2 O 3 /2 nd ZrO 2 (ZTNAZ) as insulator of DRAM capacitor with metal-insulator-metal (MIM) structure have been widely investigated [1-4]. ZAZ is one of the most candidate structure because ZrO 2 has relatively high-dielectric-constant (high-k) value (>30) and wide band gap (~5.8 eV) [1,2]. An amorphous Al 2 O 3 interlayer acts as blocking layer to suppress the leakage current through the grain boundaries of ZrO 2 layer. An annealing process was generally carried out after ZAZ deposition or TiN/ZAZ/TiN fabrication. The effects of annealing step on k-values of 1 st ZrO 2 and 2 nd ZrO 2 layers are not fully understood. In this study, we investigate k-values of ZrO 2 layer of TiN MIM capacitors with Al 2 O 3 /ZrO 2 (AZ) and ZrO 2 /Al 2 O 3 (ZA) insulators fabricated by post-deposition annealing (PDA) after AZ and ZA insulators deposition or post-metallization annealing (PMA) after TiN top electrode (TE-TiN) deposition. MIM capacitors were fabricated as follows. A 50-nm-thick TiN bottom electrode (BE-TiN) was deposited by reactive sputtering on the P + Si substrate. In case of AZ stack structure, a 2-nm-thick Al 2 O 3 layer was deposited on BE-TiN by atomic layer deposition (ALD) at 300°C using TMA and water gas, and subsequently ZrO 2 layer was deposited on Al 2 O 3 layer by ALD at 300°C using (C 5 H 5 )Zr[N(CH 3 ) 2 ] 3 precursors and water gas. On the other hand, the ZA stack structure was prepared by depositing a ZrO 2 layer and then an Al 2 O 3 layer under same ALD condition. The ZrO 2 thickness was varied from 2.8 to 5.7 nm by changing ALD cycles. PDA (ZA wPDA and AZ wPDA) was carried out at 600°C for 1 min in N 2 . Finally, a 50-nm-thick TE-TiN was deposited to fabricate MIM capacitor. TiN/AZ/TiN and TiN/ZA/TiN capacitors without PDA were also fabricated by PMA (ZA wPMA and ZA wPMA) with the same PDA conditions. All structural MIM capacitors without annealing process (w/o) were prepared as references. The k-value of Al 2 O 3 layer which estimated from capacitance of TiN/Al 2 O 3 /TiN capacitors at 0V was found to be 7.7. By using this k-value of Al 2 O 3 , each k-value of ZrO 2 layer was also estimated from capacitance at 0V. The k-values of ZrO 2 layer of all w/o capacitors exhibited about 22 - 25. The k-values of the AZ wPMA increased as the ZrO 2 thickness increased and was saturated to 35 when the thickness was over 4.8 nm. The ZA wPMA showed a similar behavior with respect to the ZrO 2 thickness, but the saturated k-value was a small value of 31. In the case of the ZA wPDA, we observed a dramatic increase in k-value of ZrO 2 layer when the ZrO 2 thickness increased from 3.9 to 4.9 nm. The maximum k-value of 44 was about 10 larger than that of the AZ wPDA under the same ZrO 2 thickness of 5.7 nm. This difference may be related with coefficients of thermal expansion (CTE) of the Al 2 O 3 (5.4~8.4 × 10 -6 K -1 ), ZrO 2 (8.0~11.0 × 10 -6 K -1 ) and TiN (9.4~10.3 × 10 -6 K -1 ). ZrO 2 had a similar CTE value of TiN and larger CTE value than Al 2 O 3 . In the case of the ZA wPDA capacitor, ZrO 2 layer was annealed with an asymmetric structure sandwiched between Al 2 O 3 and TiN with different CTE values during PDA. This asymmetric structure may introduce some stress of ZrO 2 layer and results in grain growth and crystallization of high-k phase. It is considered that the k-value became smaller because ZrO 2 layer grew freely without stress in the AZ wPDA. The ZrO 2 layer of AZ and ZA became symmetric structure by sandwiching between BE-TiN and TE-TiN, and may be suppressed the stress during PMA. To increase k-value of the ZrO 2 layer, it is important that the crystal growth of the ZrO 2 layer is carried out under stress during annealing process. This study was supported, in part, by JSPS KAKENHI (Grant Nos. JP20H02189 and JP18J22998). [1] Y.- H. Wu et al., Appl. Phys. Lett. 93 , 033511 (2008). [2] W. Weinreich et al., J. Vac. Sci. Technol. B 31 , 01A109 (2013). [3] T. Sawada et al., J. Vac. Sci. Technol. A 35 , 061503 (2017). [4] T. Onaya et al., Thin Solid Films 655 , 48-53 (2018). Figure 1