Effect of build orientation, sintering schedule, and resin cement on the bond strength of additively manufactured zirconia to dentin.

作者
Gabriela Panca Sabatini,Pedro Molinero‐Mourelle,Álvaro Limones,Gunjan Srivastava,Burak Yilmaz,Anne Peutzfeldt,Gülce Çakmak
出处
期刊:
标识
DOI:10.48620/98579
摘要

STATEMENT OF PROBLEM: Whether the manufacturing protocol (build orientation and sintering schedule) of additively manufactured (AM) zirconia impacts the bond strength compared with subtractively manufactured (SM) zirconia remains unclear. PURPOSE: The purpose of this in vitro study was to evaluate the effect of build orientation (45 degrees and vertical), sintering schedule (1-step and 2-step), and resin cement on the shear bond strength (SBS) and failure mode of AM zirconia bonded to dentin compared with that of SM zirconia. MATERIAL AND METHODS: One hundred fifty 3Y-TZP zirconia cylinders (Ø2×4 mm) were produced by AM (INNI Cera BCM-W1000) or SM (IPS e.max ZirCAD MT). AM specimens were printed vertically at 90 degrees or at 45 degrees and subjected to 1-step or 2-step sintering; SM specimens were milled and sintered. The specimens were divided into 3 subgroups to be luted to human dentin (n=10) with 3 dual-polymerizing resin cements (SpeedCEM Plus; Ivoclar AG, RelyX Ultimate; 3M Dental, Panavia V5; Kuraray Noritake Dental). Dentin and zirconia surfaces were pretreated per cement and manufacturer protocols. After 24 hours, SBS was measured, and failure modes evaluated. The data were analyzed using 2-way ANOVA to assess the effects of manufacturing technique (AM or SM) and resin cement and using 3-way ANOVA exclusively within the AM group to evaluate the effects of build orientation, sintering schedule, and resin cement, followed by Tukey post hoc tests (α=.05). RESULTS: According to the 2-way ANOVA, zirconia manufacturing technique (AM or SM) did not significantly influence SBS, whereas resin cement had a significant effect (P<.001). Within the AM groups, the 3-way ANOVA revealed that resin cement was also the only factor significantly affecting SBS (P<.001), with no significant effects of build orientation or sintering schedule (P>.05). SpeedCEM Plus (8.9 ±3.7 MPa) showed the significantly lowest SBS and RelyX Ultimate (15.1 ±5.3 MPa), and Panavia V5 (15.7 ±4.9 MPa) yielded similar SBS. No significant difference was found in failure mode between AM and SM zirconia (P=.647), but differences existed between cements (P<.001). Almost all failures (98%) in SpeedCEM Plus groups were adhesive at the dentin-cement interface. The RelyX Ultimate and Panavia V5 groups had approximately 20% adhesive and approximately 50% cohesive failures within dentin. CONCLUSIONS: No significant differences in SBS or failure mode were found between AM and SM zirconia. Build orientation and sintering schedule of AM zirconia had no influence on the bond strength of zirconia to dentin, whereas resin cement had a significant effect. In general, SpeedCEM Plus resulted in the significantly lower bond strength of AM and SM zirconia to dentin than did RelyX Ultimate or Panavia V5.

科研通智能强力驱动
Strongly Powered by AbleSci AI
科研通是完全免费的文献互助平台,具备全网最快的应助速度,最高的求助完成率。 对每一个文献求助,科研通都将尽心尽力,给求助人一个满意的交代。
实时播报
可爱的函函的应助被小笨蛋采纳,获得10
刚刚
刘承昭发布了新的文献求助10
1秒前
1秒前
过时的热狗完成签到,获得积分10
1秒前
过过过发布了新的文献求助10
2秒前
LYZ完成签到,获得积分10
2秒前
郭利敏发布了新的文献求助10
2秒前
SWAGGER123发布了新的文献求助10
3秒前
过时的不评完成签到,获得积分10
3秒前
molihuakai的应助被周一采纳,获得10
3秒前
syvshc的应助被u485910采纳,获得10
3秒前
无极微光的应助被陶瓷小罐采纳,获得20
4秒前
玩家666发布了新的文献求助10
4秒前
泷生发布了新的文献求助10
5秒前
小蘑菇的应助被shd采纳,获得10
5秒前
彭于晏的应助被刘承昭采纳,获得10
6秒前
7秒前
英姑的应助被xiaohu采纳,获得10
8秒前
妮娜完成签到,获得积分10
8秒前
molihuakai的应助被meng采纳,获得10
9秒前
月亮不营业完成签到,获得积分10
9秒前
秋风的应助被Jasmine采纳,获得10
9秒前
9秒前
9秒前
专注的小霸王完成签到,获得积分20
10秒前
10秒前
嘻嘻完成签到,获得积分10
10秒前
科研通AI65的应助被正直的南烟采纳,获得10
11秒前
i3utter发布了新的文献求助10
11秒前
旅程完成签到 ,获得积分10
11秒前
思源的应助被darkegg采纳,获得10
11秒前
香蕉觅云的应助被过过过采纳,获得10
11秒前
11秒前
12秒前
周而复始@完成签到,获得积分10
12秒前
12秒前
Lalalili完成签到,获得积分10
12秒前
dgbsw完成签到,获得积分10
12秒前
13秒前
CipherSage的应助被昏睡的金毛采纳,获得10
13秒前
高分求助中
(应助此贴封号)【重要!!请各用户(尤其是新用户)详细阅读】【科研通的精品贴汇总】 10000
拉伸高分子熔体中缠结行为的模拟和小角中子散射研究 2000
Handbook of Sport Coaching Research 1000
Orthognathic Surgery - 2 Volume Set 500
高分子基功能界面水蒸发材料与应用研究 500
外场增强的水汽发电研究 500
基于结构调控的功能化水诱导发电材料与器件研究 500
热门求助领域 (近24小时)
化学 材料科学 医学 生物 纳米技术 计算机科学 工程类 有机化学 化学工程 生物化学 物理 复合材料 内科学 催化作用 光电子学 人工智能 细胞生物学 无机化学 物理化学 数学
热门帖子
关注 科研通微信公众号,转发送积分 8193653
求助须知:如何正确求助?哪些是违规求助? 9579816
关于积分的说明 21867585
捐赠科研通 7793288
什么是DOI,文献DOI怎么找? 3437343
关于科研通互助平台的介绍 2560779
邀请新用户注册赠送积分活动 2484193